Choose Language

Technical guide

Marine Galley Ventilation Systems: Standards, Calculations and Installation

By Ercan KeskinPublished on 28 March 20268 min read

In brief

  • Plan at least 60-80 m³/h of extraction capacity per kW of thermal load, and size the hood to the actual cooking equipment.
  • Fire dampers at compartment penetrations and easily removable grease filters are core SOLAS II-2 requirements for galley exhaust systems.
  • Supply make-up air equal to 80-90% of exhaust capacity; otherwise negative pressure reduces extraction and disturbs flames.
Contents
  1. 1. Why Is Ventilation Critical in a Marine Galley?
  2. 2. Airflow Calculation: CFM and m³/h
  3. 3. SOLAS and Class Society Standards
  4. 4. Hood Selection and Technical Criteria
  5. 5. Exhaust Fan and Duct System
  6. 6. Make-Up Air: Balancing the Fresh Air Supply
  7. 7. Installation and Fitting Rules
  8. 8. Periodic Maintenance
  9. Frequently asked questions

A ship's galley, or marine kitchen, is an enclosed and restricted space that generates high heat, humidity and grease vapour. Without adequate ventilation, these conditions directly harm crew health, fire safety and the service life of the galley equipment.

A marine galley ventilation system is more than a hood and an extraction fan. Correct airflow calculation, SOLAS fire safety requirements, class society standards and compatibility with the ship's electrical system must all be addressed together. In this guide we explain these topics step by step.

1. Why Is Ventilation Critical in a Marine Galley?

If ventilation is inadequate in a restaurant kitchen ashore, a window or door is opened. On a ship this is not possible. The galley is inside a closed steel box, and the heat, humidity, grease vapour and combustion gases it produces can leave only through purpose-designed exhaust ducts.

The consequences of inadequate ventilation:

  • Fire risk: Grease accumulating in the hood grease filters is a source of ignition. SOLAS contains specific provisions on this.
  • Crew health: A build-up of CO, NO₂ and grease vapour causes respiratory problems in the long term.
  • Equipment life: Condensing moisture and grease cause premature failure in galley equipment and electrical systems.
  • Class survey: An inadequate ventilation system can be grounds for a non-conformity at class survey.

2. Airflow Calculation: CFM and m³/h

Ventilation capacity is expressed in two units: CFM (cubic feet per minute, the American/maritime standard) and m³/h (cubic metres per hour, the European standard). Conversion: 1 CFM ≈ 1.699 m³/h.

2.1 Calculation Methods

Marine galley ventilation capacity can be calculated using three basic methods:

Method Formula / Rule Use Case
Volume-basedGalley volume × 30-60 air changes per hourPreliminary calculation and small galleys
Thermal-load-basedTotal thermal load (kW) × 0.8 m³/h/kW factorProjects with intensive cooking equipment
Hood capture velocityHood opening area (m²) × 0.3-0.5 m/s capture velocityHood sizing

2.2 Reference Values by Vessel Type

Vessel Type Crew Estimated Extraction Capacity Air Changes
Small cargo ship10-15 persons1,500 – 2,500 m³/h30-40 per hour
Medium-size cargo/container ship20-30 persons3,000 – 5,000 m³/h40-50 per hour
Offshore support vessel50+ persons6,000 – 10,000 m³/h50-60 per hour
Ferry / passenger shipVariableProject-specific calculation60+ per hour
Yacht / superyacht5-20 persons800 – 2,000 m³/h25-35 per hour

* These values are given for preliminary calculation only. For final sizing, equipment thermal loads and galley geometry must be assessed together.

3. SOLAS and Class Society Standards

Marine galley ventilation systems must be designed in accordance with SOLAS II-2 (fire protection) and the galley ventilation rules of the class societies.

Key SOLAS II-2 Requirements

  • Hoods over cooking equipment must be made of fire-resistant material or be fitted with a fire suppression system.
  • Exhaust ducts must be fitted with fire dampers where they pass through compartment boundaries.
  • To prevent grease build-up, hood filters must be easy to remove and clean.
  • Integration of automatic fire extinguishing systems (Ansul or similar) is mandatory on large commercial ships.
Class Society Hood Standard Exhaust Duct Thickness
DNV GLDNVGL-RU-SHIP Pt.4 Ch.8Min. 1.5 mm steel
Lloyd's RegisterLR Rules Pt.5 Ch.16Min. 1.5 mm steel
Bureau VeritasBV NR 566Min. 1.5 mm steel
Türk LoyduTL Machinery Rules, Section 13Min. 1.5 mm steel

4. Hood Selection and Technical Criteria

The hood is the most critical component of the ventilation system. It must be correctly sized to capture grease, vapour and heat at the source.

4.1 Hood Types

Type Application Advantage
Wall-mountedCooking lines against a bulkheadCompact, ideal for restricted galleys
Island (suspended from the deckhead)Centrally located cooking islandsCapture from all sides, for large galleys
Built-in (recessed)Yacht and superyacht projectsAesthetic, no visible ductwork
Low-profileVehicle deck and boat projectsSuits low deckhead clearance

4.2 Filter Systems

Three filter types are used in marine hoods:

  • Baffle filter: The most common type. Grease particles strike the baffle surface and run off through the drainage channel. Removable and dishwasher-cleanable. SOLAS compliant.
  • Cassette filter: Additional protection against finer grease particles. Fitted behind the baffle filter.
  • Activated carbon filter: An additional layer for odour removal. Preferred in yacht projects for interior comfort.

5. Exhaust Fan and Duct System

The exhaust fan is the heart of the system. Land-type industrial fans cannot be used in marine applications.

Points to Consider When Selecting a Fan

  • Voltage / frequency: 440V/60Hz or 380V/50Hz; the fan must suit the ship's electrical system
  • Grease resistance: Fan blades and casing must be made of material resistant to grease vapour
  • Static pressure capacity: It must cover the static pressure loss calculated from duct length and number of bends
  • Speed control: Variable speed via a frequency inverter, with automatic adjustment to cooking intensity
  • Vibration isolation: Marine fans must be mounted with vibration-damping connectors

Duct System

Parameter Recommended Value Explanation
Duct air velocity5–8 m/sKeeps noise low and prevents grease build-up
Duct wall thicknessMin. 1.5 mm steelClass society standard
Number of bendsAs few as possibleEvery bend creates static pressure loss
Cleaning accessCleaning hatch every 3 metresSOLAS grease build-up prevention rule
Fire damperMandatory at compartment penetrationsRequired by SOLAS II-2

6. Make-Up Air: Balancing the Fresh Air Supply

The most common mistake is to design the exhaust system and forget the fresh air inlet. If fresh air equal to the volume removed by the exhaust is not supplied, the system operates under negative pressure: doors will not open, extraction performance drops and flames flicker.

Golden rule: Provide make-up air equal to 80-90% of the exhaust capacity. The remaining 10-20% keeps the galley at a slight negative pressure, which prevents galley air from leaking into adjacent spaces.

Make-Up Air Source Advantage Disadvantage
Natural transfer (gap under the door)Simple, no costUncontrollable, galley pressure fluctuates
Dedicated make-up air duct systemControlled and balanced flowAdditional cost and installation
Air-conditioning system circuitHeating/cooling integrationRequires coordination with the HVAC system

7. Installation and Fitting Rules

Critical rules to observe when installing a marine ventilation system:

  • The distance between the lower edge of the hood and the cooking surface should be 650–900 mm (depending on type and thermal load)
  • The hood should be at least 150 mm wider than the cooking equipment on each side
  • The exhaust duct should be designed as short as possible with few bends
  • Fire dampers must be fitted at all compartment penetrations
  • The fan should be positioned so that it is the highest point of the system, to prevent grease build-up
  • The duct system should be fitted with a cleaning hatch every 3 metres
  • The installation should be approved by the naval architect
  • Class society survey should be planned in advance

8. Periodic Maintenance

Even the best-designed ventilation system becomes a fire risk if it is left unmaintained. Recommended maintenance schedule:

Maintenance Item Frequency Note
Baffle filter cleaningWeekly for heavy useDishwasher compatible
Hood interior cleaningMonthlyEspecially the grease drainage channel
Exhaust duct internal cleaningEvery 6 monthsVia the cleaning hatches
Fan inspection and lubricationEvery 3 monthsIncluding vibration and noise checks
Fire damper testEvery 6 monthsThe class society may require it
Make-up air balance checkAnnuallyWith a measuring instrument

Related content:
→ Marine Galley Equipment — Technical details of ranges, ovens and cooking groups
→ Custom-Size Stainless Steel Fabrication — Custom AISI 316L hood manufacture
→ Marine Galley Range Guide

A Ventilation Solution for Your Project

Share your galley plan, equipment list and class requirements, and we will design a custom-size hood and ventilation system.

Frequently asked questions

Can a standard land-type hood be used on a ship?

No. Land-type hoods are not designed to withstand a ship's roll and vibration. They also fail to meet the SOLAS requirements on exhaust duct wall thickness and fire dampers, which gives grounds for a non-conformity at class survey.

How large should the hood be?

The hood should be at least 150 mm wider than the cooking equipment beneath it on each side. Its height should be set so that the distance between the cooking surface and the lower edge of the hood is 650-900 mm. Exact dimensions are determined by the thermal load calculation.

Why is make-up air important?

If fresh air equal to the volume taken by the exhaust system is not supplied, excessive negative pressure builds up in the galley. Extraction performance then drops, doors will not open and flames can flicker. Plan make-up air at 80-90% of the exhaust capacity.

How often should grease filters be cleaned?

In heavily used commercial ship galleys, baffle filters should be cleaned at least once a week. Uncleaned filters create a serious fire risk because of grease build-up.

What is needed to order a custom-size hood?

A technical drawing of the galley or an on-site survey, the list of cooking equipment with thermal ratings, the ship's electrical system (440V/60Hz or 380V/50Hz) and the project's class society are sufficient. If there is no drawing, we carry out an on-site survey.

Do you install on shipyard projects in Türkiye?

Yes. From our production centre in Gebze we deliver and install on site at shipyards in Türkiye and on export projects worldwide. Planning follows the shipyard's project schedule.

EK
Ercan Keskin
Founder of ONLYMARITIME

Ercan Keskin has worked in the maritime sector since 2014: galley design for naval, commercial and yacht projects, technical drawing, purchasing, installation and after-sales service. He founded ONLYMARITIME in 2020. LinkedIn

Send us your drawing or equipment list

Tell us the vessel type, the electrical data and the delivery port, and we will come back to you with a technical and commercial proposal.

Chat on WhatsApp