In brief
- Quotations are only comparable if sheet thickness, profile size and surface finish are stated in writing, not just the material grade.
- At sea, loads arrive as impacts in roll and pitch, so reinforcement under the top matters as much as the top itself.
- Rust usually comes from workmanship: shared grinding tools, uncleaned weld burn, carbon steel frames and gaps left by intermittent welds.
Contents
- 1. The Same Product, Different Sheet and Different Finish
- 2. Support Under the Top: What Happens in a Roll?
- 3. Installation Done as if It Would Never Be Removed
- 4. The Result of Poor Workmanship: Rust and "Bleeding"
- 5. Weld Gaps and the Risk of Bacteria
- 6. Five Questions to Ask When Comparing Quotations
- Frequently asked questions
Anyone who collects quotations notices the same thing: the dimensions are the same, the product description is the same, the photographs match, yet the prices differ greatly. The decision usually goes to the lowest price. In a stainless steel marine galley worktop, however, the difference hides in a few points that never show on paper.
As a team that looks at fabrication from the inside, ONLYMARITIME knows well where these differences hide. In this article we share five points that are easily overlooked when comparing quotations.
Ercan Keskin — Founder of ONLYMARITIME. Has been involved in the fabrication and installation of ship and yacht galleys, cold rooms and laundry systems since 2014. The ONLYMARITIME team produces custom-size marine galley equipment from AISI 304/316L stainless steel. In brief: When comparing quotations for stainless steel marine worktops, look at five points: (1) Are the sheet thickness, profile size and surface finish stated in writing? (2) Is there adequate reinforcement under the top? (3) Can the unit be dismantled, or is it fitted as if it would never be removed? (4) Are the internal frame and reinforcements also stainless steel? (5) Are the welds continuous and clean, or are gaps left in the corners? In this article
1. The Same Product, Different Sheet and Different Finish
Two products sold on the market as a "stainless steel worktop" may be made of the same material, but that does not make them the same product. One may be made with 1.5 mm sheet and the other with 0.8 mm sheet. The same applies to the supporting profiles: a 40x40x2 profile and a 30x30x1 profile look alike at first glance, but not once a load is applied.
Surface quality is a separate matter. A properly finished, smooth surface is both easier to clean and holds less salt and dirt. A rough or scratched surface is a candidate for staining from the first day.
If a quotation does not state the sheet thickness, profile size and surface finish alongside the material grade, it cannot be compared with the others.
2. Support Under the Top: What Happens in a Roll?
Ashore, a heavy piece of equipment is placed on a worktop and stays there for years. On a ship, that load is never static. In a roll, in pitching or in a sudden loss of balance, the equipment lands on the top as an impact; sometimes something falls onto it as well.
If adequate reinforcement has not been placed under the top, thin sheet eventually sags, ripples or cracks at the welds. If a heavy item such as a combi oven or a mixer will stand on it, the underside of the top is at least as important as the upper side.
When requesting a quotation, ask what is placed under the top and how the equipment will be fixed to the worktop. If this detail is not in the drawing, it is most likely not in the product either.
3. Installation Done as if It Would Never Be Removed
Some installations are done as if the equipment will never move again. The legs are welded directly to the deck, the worktop is welded to the bulkhead, the back is sealed with silicone, and no way is left to reach the drain and connections.
On installation day everything looks clean. The problem appears at the first breakdown or the first serious clean. Having to cut the worktop to reach a blocked drain, or never being able to reach the dirt that collects behind a panel that cannot be removed, costs both time and money on a ship. And when a worktop welded to the deck has to be replaced or repositioned, the job turns into a small modification of cutting and re-welding.
These jobs often have to be done during a voyage or within a limited shipyard period, whereas properly designed demountability reduces the same job to a few hours.
On a ship, fixing the equipment is essential, but fixing it and making it impossible to remove are not the same thing. In a good fit-out, every point that will need service is thought through in advance: bolted fixing to the deck, removable panels, accessible drain and pipework. The back of a unit should either be completely closed and sealed, or open enough to be cleaned easily. The middle ground is the worst.
4. The Result of Poor Workmanship: Rust and "Bleeding"
If rust appears on stainless steel furniture, the cause is usually workmanship rather than material.
The most common causes are as follows: iron dust left on the surface by grinding discs and brushes shared with carbon steel, burn marks left uncleaned after welding, and carbon steel used in the internal frame or reinforcements to cut costs. The last one is invisible from outside, but it reveals itself when rust begins to seep from the joints; in the field this is called "bleeding".
None of these problems is visible on delivery day. They emerge after a few months of salt air and humidity. Sometimes they can be cleaned; sometimes the part has to be replaced.
5. Weld Gaps and the Risk of Bacteria
In a kitchen, hygiene is not only about the visible surface. The thin gaps left between two sheets joined by tack or intermittent welding are an ideal hiding place for water, grease and food residue. Neither a cloth nor a brush can reach these gaps; over time they become a source of bacteria and odour.
The same gaps are a corrosion risk too. Salt water collects there, and it becomes the place where stainless steel is at its weakest.
The right approach is clear: continuous welds, ground and finished seams, and rounded corners wherever possible. Looking underneath and into the corners of a marine galley unit is the fastest way to understand how it has been made.
6. Five Questions to Ask When Comparing Quotations
- Are the sheet thickness, profile size and surface finish stated in writing?
- Is there reinforcement under the top, and how will heavy equipment be fixed?
- How is the unit fixed to the deck and bulkhead, and can it be dismantled when necessary?
- Are the internal frame and reinforcements also stainless steel?
- Are the welds continuous and clean, or are gaps left in the corners?
The price in the quotation is the figure you pay on delivery day. Looking at these five points shows you the real cost before the ship goes to sea.
Need help comparing quotations?
Let us go through the quotations you have received for your galley together, and explain what to look for, from sheet thickness to installation detail.
Related
- The first version of this article on LinkedIn: Ercan Keskin — LinkedIn
Frequently asked questions
What sheet thickness is sufficient for a stainless steel marine worktop?
It depends on the load the worktop will carry and how intensively it is used. What matters is that the sheet thickness and supporting profile size are clearly stated in the quotation; the description "stainless steel worktop" alone is not enough for comparison.
Why does a marine galley worktop need reinforcement underneath?
Unlike static loads ashore, roll and pitching put equipment onto the top as an impact. Without adequate reinforcement, thin sheet eventually sags or cracks at the welds.
Should marine galley equipment be welded or bolted to the deck?
Fixing equipment is essential on a ship, but fixing it and making it impossible to remove are different things. Bolted fixing to the deck and removable panels allow service and maintenance access without cutting the worktop.
Why does stainless steel rust?
The cause is most often workmanship rather than material: iron dust left by grinding equipment shared with carbon steel, uncleaned weld burn, or carbon steel used in the internal frame will return as rust stains within months.
Why are weld gaps risky?
Cleaning equipment cannot reach the thin gaps left by tack or intermittent welding. These gaps become a source of bacteria and odour, and a starting point for corrosion as salt water collects. Continuous welds and ground seams remove this risk.
